ZEP 8 Report post Posted May 1, 2016 Hello: Can someone answer my question: I've been using Torque app in my smarphone for quite along. I can register oil temp after adding pid details. A week ago I've changed my smartphone to a Samsung S/ Edge. When I tried to add the oil temp PID the menu shows two new items: Diagnostic Start Command and Diagnostic Stop Command I tried with those in blank but it doesn't work. Ayny ideas? Share this post Link to post Share on other sites
long-gone 152 Report post Posted May 2, 2016 Nope, but I'd like to know how to access oil temperature too, so here's a bump. Share this post Link to post Share on other sites
DanJ 374 Report post Posted May 2, 2016 I used the details from the second post here: http://www.ft86club.com/forums/showthread.php?t=23530 It works for me with blanks in the diagnostic start and stop fields. 1 long-gone reacted to this Share this post Link to post Share on other sites
long-gone 152 Report post Posted May 2, 2016 Nice one. Ta. Share this post Link to post Share on other sites
nerdstrike 186 Report post Posted May 2, 2016 Wow, what a long and mostly empty thread (the FT86 one). The only useful thing in it is the oil temp part, the rest is just confused people. The accuracy of some of the other elements requires a sensible car weight. Share this post Link to post Share on other sites
DanJ 374 Report post Posted May 2, 2016 Yep! I tried the fuel left PID as well and it's complete bollocks, but oil temp works a treat. Share this post Link to post Share on other sites
Lauren 2259 Report post Posted May 2, 2016 I think the oil temp of the Torque App is it's one very useful function. I did a bit of testing three years ago at a very hot Donny where it was 35C. Found I was getting oil temps at 125C after a couple of laps, so found it best to ease off down the straights. Interestingly it didn't seem to really get any higher though. Share this post Link to post Share on other sites
Rich 378 Report post Posted May 2, 2016 37 minutes ago, DanJ said: Yep! I tried the fuel left PID as well and it's complete bollocks, but oil temp works a treat. I have a working fuel left PID, seems pretty good to me; showing ~50 litres just after a fill and seems accurate after that. It required a little bit of fiddling to get it spot on as I recall. 18 minutes ago, Lauren said: I think the oil temp of the Torque App is it's one very useful function. I did a bit of testing three years ago at a very hot Donny where it was 35C. Found I was getting oil temps at 125C after a couple of laps, so found it best to ease off down the straights. Interestingly it didn't seem to really get any higher though. My oil temp got to ~130C within a lap or two at Snetterton but doesn't really go above that. Seems like my manifold adds a bit of heat soak. Maybe I should look into an oil cooler. Share this post Link to post Share on other sites
nerdstrike 186 Report post Posted May 2, 2016 The default fuel level PID in Torque is probably quite sufficient. Not that it helps you unless you're flat-lining the fuel gauge. Share this post Link to post Share on other sites
Rich 378 Report post Posted May 2, 2016 In case anyone is interested, my fuel remaining PID is: PID: 2129 Min Value: 0 Max Value: 55 Scale Value: x1 Unit Type: l Equation: ((A/95.0)*50) ODB Header: 7C0 Gives fuel remaining in litres. Share this post Link to post Share on other sites
long-gone 152 Report post Posted May 3, 2016 Why 95 not 100? Are you allowing 5% fudge factor? Share this post Link to post Share on other sites
Test Drives Unlimited 278 Report post Posted May 3, 2016 I got Gauges in my car now which give useful readings going around the track Oil Temp got up to 101c going round Snetterton the other week !! Oil Pressure was reading about 3.5 bar Voltage was reading 14.9 Water Temp was in the High 90's ! Sent from my Archos 53 Platinum using Tapatalk Share this post Link to post Share on other sites
nerdstrike 186 Report post Posted May 3, 2016 49 minutes ago, daidaiiro said: Why 95 not 100? Are you allowing 5% fudge factor? I certainly would. The fuel pumps don't like being run to the last drop, and the accuracy is off when you're either very full, going round corners fast, or otherwise below the minimum measurable. Does the '86 have a saddlebag fuel tank? If so then it's already approximating both sides. Share this post Link to post Share on other sites
Rich 378 Report post Posted May 3, 2016 2 hours ago, daidaiiro said: Why 95 not 100? Are you allowing 5% fudge factor? You're assuming it reads as 100 for full scale... 95 is "because it works"; it reads 50l when you have just filled up and decreases by the right amount. It's adapted from the stuff on ft86 where they tested various numbers while filling the tank with known amounts of fuel. Share this post Link to post Share on other sites
ZEP 8 Report post Posted May 3, 2016 Remaining fuel: Unit: I = Inch (?) Unit: L = Litre(?) Share this post Link to post Share on other sites
Rich 378 Report post Posted May 3, 2016 That's a lower-case 'L', i.e. 'l', not a capital 'i'. It's litres. Share this post Link to post Share on other sites
long-gone 152 Report post Posted May 3, 2016 1 hour ago, Rich said: You're assuming it reads as 100 for full scale... 95 is "because it works"; it reads 50l when you have just filled up and decreases by the right amount. It's adapted from the stuff on ft86 where they tested various numbers while filling the tank with known amounts of fuel. The tank has a 55 litre capacity, no? I'll add a display for each and see which one works out best. Share this post Link to post Share on other sites
ZEP 8 Report post Posted May 3, 2016 Thanks. Oil Temp and Fuel remain OK. Any other Custom PIDS to add? Share this post Link to post Share on other sites
Rich 378 Report post Posted May 3, 2016 2 hours ago, daidaiiro said: The tank has a 55 litre capacity, no? I'll add a display for each and see which one works out best. No, it's a 50 litre tank. Share this post Link to post Share on other sites
Church 209 Report post Posted May 3, 2016 But i guess above tank's itself 50lr there might be also some capacity in fuel lines & tube from tank till fill cap, if one has habit to fill full till first auto-cutoff(?), and then more some. I sometimes think about borrowing small extra can of fuel and just for experiment sake run once till completely dry of fuel, just so to know how much there can be .. Share this post Link to post Share on other sites
long-gone 152 Report post Posted May 3, 2016 I've thought the same, but running genuinely dry may suck in some nasties. Happy for you to try though. Share this post Link to post Share on other sites
Keethos 842 Report post Posted May 6, 2016 Do you need to be worried about sucking up nasties on a new/relatively new car? Share this post Link to post Share on other sites
nerdstrike 186 Report post Posted May 6, 2016 The fuel syphon is from the bottom of the tank. If the filter works, you'll only consume the filth that fits through it. That same filth will be agitated on every fill, so it's not like it's being kept somewhere safe until your rainiest day. I can confirm the oil temp PID mentioned earlier works a treat. Fairly convincing numbers, with sensible oil temperature being achieved a bit after the water hits the normal mark on the temp gauge (which seems to be damped above about 80 Celsius). Share this post Link to post Share on other sites
keelerad 256 Report post Posted August 19, 2017 My post with links to youtube vids Share this post Link to post Share on other sites