rob275 1817 Report post Posted March 22, 2014 I woke up this morning looking at the weather, it was sunny outside with a few black clouds, I didn't know whether to crack on with the detail today or leave it until next weekend. Metcheck said it was currently raining and BBC Weather said it was going to rain until 3pm. Still unsure at about 10:30 I gathered up my bits to begin tackling this, my plan was initially to wash the car down, Iron-X and clay it ready for polishing. As it happened it didn't rain at 3pm and the BBC forcast said it was going to be dry for the rest of the afternoon/evening so I figured i'd carry on with the polishing. Items used: - 4 New Microfibre cloths - Karcher pressure washer - DAS-6 PRO Dual Action Polisher - Menzerna PF2300 - Menzerna SF4500 - Polishing Pad - Finishing Pad - PH Neutral Snow Foam - The remains of my AG Shampoo - Wash Mitt - 2 Buckets - Gtechniq C1 - Gtechniq G4 - Gtechniq G1 - Gtechniq G2 My first step was to snow foam the car to remove any larger bits of grit etc I then washed it off with the pressure washer lance after i'd left it for 10mins ish I then washed the car using two buckets, rinsing each panel at a time I then Applied Iron-X to the paintwork doing a few panels at a time (This stuff stinks I was gagging on it, but it works!) Rinsed Iron-X off after 3-5 minutes of curing Snow Foamed again and rinsed Back on the driveway to begin claying the entire car Car was then pretty much ready to begin the polishing... I used Menzerna PF2300 on panels that had some swirls, mainly the bonnet, roof, rear quarters and SF4500 over the all the panels afterwards. This is where I have got to, I need to wipe down with Alcohol tomorrow and apply Gtechniq C1 then prep the windows up to be done. Will put pictures up tomorrow of the finished product and some in between bits. Haven't taken a lot though as I needed to get it done! Update: This morning up at 8am, dried the car, wiped all panels down with Gtechniq Panel Wipe Polished front & read windows with G4 Applied Gtechniq G1 to windows (at this point it started drizzling during curing and i got a bit mad, but it worked) Left to cure for 15 minutes and applied G2 to remove residue from the G1 Applied C1 to all panels and shot off to the Grass hopper meet, so Images are Post grasshopper meet. Share this post Link to post Share on other sites
forge197 12 Report post Posted March 23, 2014 Look forward to seeing the pictures did a full detail of my daily driver a couple weeks ago it's pretty satisfying when all done. Share this post Link to post Share on other sites
Twigman 93 Report post Posted March 23, 2014 Look forward to seeing your motor later at Westerham perhaps? Share this post Link to post Share on other sites
rob275 1817 Report post Posted March 23, 2014 Snowfoam: Iron X working: After wash: Finished Car after drive to grasshopper and back: I'm far too lazy to get proper pictures, my back hurts and I just want to sleep Share this post Link to post Share on other sites
Keethos 842 Report post Posted March 23, 2014 LOL, you wearing yellow Marigolds? Looks good though.....the Marigolds I mean Share this post Link to post Share on other sites
rob275 1817 Report post Posted March 23, 2014 LOL, you wearing yellow Marigolds? Looks good though.....the Marigolds I mean haha yeah, I needed to stuff I was using was literally burning my hands, lack of latex gloves meant I had to nick the yellow marigolds sitting in the kitchen! Share this post Link to post Share on other sites
forge197 12 Report post Posted March 23, 2014 Nice end result. Share this post Link to post Share on other sites
